APPLICATIONS OF THE MOC3011 TRIAC DRIVER DOWNLOAD

If the second input of a 2 input gate is tied to a simple timing circuit, it will also provide energization of the triac only at the zero crossing of the ac line voltage as shown in Figure To allow a safety margin and ensure long service life, the MOC is actually tested to trigger at a value lower than the speci? These output detector chips are designed to drive triacs controlling loads on and V AC power lines. Built-in element to absorb a surge current derived from changing motor direction More information. Phototriac, Zero Crossing, 1. Since the triac turns off at zero current, it may be trying to turn off when the applied current is zero but the applied voltage is high. This application note describes circuits in which these More information.

Uploader: Kazizragore
Date Added: 27 February 2006
File Size: 8.80 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 59613
Price: Free* [*Free Regsitration Required]

A Introduction The Thyristor family of semiconductors consists of several very useful devices.

Application Note AN Applications of Non Zero Crossing Triac Drivers Featuring the MOC PDF

Output Filter Design More information. Since the triac turns off at zero current, it may be trying to turn off when the applied current is zero but the applied voltage is high. When the designer has more thw of the input and output conditions, he can eliminate those components which are needed for his particular application to make the circuit more cost effective.

The open-collector outputs require external pull-up More information. A Survey of Zero-Knowl Description The SX is a bi-directional, single-pole, single-throw, normally open multipurpose solid-state relay. There are numerous ways to increase this current to a level compatible with the input requirements; an efficient way is to use the Fairchild TinyLogic, NC7SZ0 shown in Figure 5.

  CITIZEN PROLASER 6000 DRIVER DOWNLOAD

The resistor should be chosen to set the current into the LED to be a minimum of 10 mA but no more than 50 mA. Line Reactors and AC Drives Rockwell Automation Mequon Wisconsin Quite often, line and load reactors are installed on AC drives without a solid understanding of why or what the positive and negative consequences.

In the on state, the detector will pass mA in either direction with less than 3 V drop Figure 1.

In the on state, the detector will pass ma in either direction with less than 3 V drop Figure 1. In order to applicaations a snubber properly, one should really know the power factor of the reactive load, which is de?

In each More information. The open-collector outputs require external pull-up. The detector has a minimum blocking voltage of Vdc in either direction in the off state.

Application Notes: TRIAC Driver Optocouplers

In some cases, this may require two snubbers-one for the triac and one for the MOC Featuring very high commutation levels and high surge current capability. In many applications the snubber used for the will also adequately protect the triac. The detector chip is a complex device which functions in the same manner as a small triac, generating the signals necessary to drive the gate of a larger triac such as Fairchild s.

It has the same pin-out as More information. When used this way, two resistors are required to equalize the voltage dropped across them as shown in Figure 7.

K AC Resistive. Posets of annular non In practice, this would be a or ohm resistor. The detector has a minimum blocking voltage of 50 Vdc in either direction in the off state. By itself, it will supply output currents up to ma; More information.

  A4TECH MODEL PK-935 DRIVER

The circuit shown in Figure 6 allows a non-critical range of input voltages to properly drive the Applicaitons and at the same time protects the input Applicatikns from inadvertent application of reverse polarity. Unfortunately, this is not always known, and this makes snubbing network design somewhat empirical. This is not quite enough to drive the MOC, nor can it be connected directly moc30011 an SCR or triac, because computer common is not normally referenced to one side of the ac supply.

Incandescent lamps can sometimes draw a peak current known as flashover which can be extremely high, and the triac should be protected by a fuse or rated high enough to sustain this current. In many applications the snubber used for the MOC will also adequately protect the triac.

Application Notes

However, a method of designing a snubber network may be de? A 4-bit address code determines More information.

If the second input of a 2 input gate is tied to a simple timing appplications, it will also provide energization of the triac only at the zero crossing of the ac line voltage as shown in Figure The motor is driven by a circuit mounted near the motor and.